Note

Hello, welcome to the SunFounder Raspberry Pi & Arduino & ESP32 Enthusiasts Community on Facebook! Dive deeper into Raspberry Pi, Arduino, and ESP32 with fellow enthusiasts.

Why Join?

  • Expert Support: Solve post-sale issues and technical challenges with help from our community and team.

  • Learn & Share: Exchange tips and tutorials to enhance your skills.

  • Exclusive Previews: Get early access to new product announcements and sneak peeks.

  • Special Discounts: Enjoy exclusive discounts on our newest products.

  • Festive Promotions and Giveaways: Take part in giveaways and holiday promotions.

👉 Ready to explore and create with us? Click [here] and join today!

3.1.8 Password Lock

Introduction

In this project, we will use a keypad and a LCD to make a combination lock. The LCD will display a corresponding prompt for you to type your password on the Keypad. If the password is input correctly, “Correct” will be displayed.

On the basis of this project, we can add additional electronic components, such as buzzer, LED and so on, to add different experimental phenomena for password input.

Required Components

In this project, we need the following components.

../_images/list_Password_Lock.png

It’s definitely convenient to buy a whole kit, here’s the link:

Name

ITEMS IN THIS KIT

LINK

Raphael Kit

337

Raphael Kit

You can also buy them separately from the links below.

COMPONENT INTRODUCTION

PURCHASE LINK

GPIO Extension Board

BUY

Breadboard

BUY

Jumper Wires

BUY

Resistor

BUY

I2C LCD1602

BUY

Keypad

-

Schematic Diagram

T-Board Name

physical

wiringPi

BCM

GPIO18

Pin 12

1

18

GPIO23

Pin 16

4

23

GPIO24

Pin 18

5

24

GPIO25

Pin 22

6

25

GPIO17

Pin 11

0

17

GPIO27

Pin 13

2

27

GPIO22

Pin 15

3

22

SPIMOSI

Pin 19

12

10

SDA1

Pin 3

SCL1

Pin 5

../_images/Schematic_three_one9.png

Experimental Procedures

Step 1: Build the circuit.

../_images/image262.png

Step 2: Change directory.

cd ~/raphael-kit/c/3.1.8/

Step 3: Compile.

gcc 3.1.8_PasswordLock.cpp -lwiringPi

Step 4: Run.

sudo ./a.out

After the code runs, use the keypad to enter the correct password: 1984. If the “CORRECT” appears on LCD1602, there is no wrong with the password; otherwise, “WRONG KEY” will appear.

Note

  • If there is an error prompt wiringPi.h: No such file or directory, please refer to Install and Check the WiringPi.

  • If you get Unable to open I2C device: No such file or directory error, you need to refer to I2C Configuration to enable I2C and check if the wiring is correct.

  • If the code and wiring are fine, but the LCD still does not display content, you can turn the potentiometer on the back to increase the contrast.

Code Explanation

#define ROWS  4
#define COLS  4
#define BUTTON_NUM (ROWS * COLS)
#define LENS  4

unsigned char KEYS[BUTTON_NUM] {
'1','2','3','A',
'4','5','6','B',
'7','8','9','C',
'*','0','#','D'};

char password[LENS]={'1','9','8','4'};

Here, we define the length of the password LENS, storage matrix keyboard key value array KEYS and the array that stores the correct password.

void keyRead(unsigned char* result);
bool keyCompare(unsigned char* a, unsigned char* b);
void keyCopy(unsigned char* a, unsigned char* b);
void keyPrint(unsigned char* a);
void keyClear(unsigned char* a);
int keyIndexOf(const char value);

There is a declaration of the subfunctions of the matrix keyboard code, refer to 2.1.8 Keypad of this document for more details.

void write_word(int data);
void send_command(int comm);
void send_data(int data);
void lcdInit();
void clear();
void write(int x, int y, char const data[]);

There is a declaration of the subfunctions of LCD1062 code, refer to 1.1.7 I2C LCD1602 of this document for more details.

while(1){
        keyRead(pressed_keys);
        bool comp = keyCompare(pressed_keys, last_key_pressed);
        ...
                testword[keyIndex]=pressed_keys[0];
                keyIndex++;
                if(keyIndex==LENS){
                    if(check()==0){
                        clear();
                        write(3, 0, "WRONG KEY!");
                        write(0, 1, "please try again");
                        }
                ...

Read the key value and store it in the test array testword. If the number of stored key values is more than 4, the correctness of the password is automatically verified, and the verification results are displayed on the LCD interface.

int check(){
    for(int i=0;i<LENS;i++){
        if(password[i]!=testword[i])
        {return 0;}
    }
    return 1;
}

Verify the correctness of the password. Return 1 if the password is entered correctly, and 0 if not.

Phenomenon Picture

../_images/image263.jpeg